Skip to end of metadata
Go to start of metadata
You are viewing an old version of this page. View the current version.
Compare with Current
View Page History
« Previous
Version 6
Next »
| Conductor Web GUI | Configure a Static Route |
|---|
| Troubleshoot > Routing tables >
|
| Branch config file |
admin@node1.seabo1# show config running
config
authority
name CompanyX
conductor-address 192.168.7.99
remote-login
exit
router seabo1
name seabo1
location Sea
location-coordinates +47.6062-122.3321/
system
log-level warning
exit
node node1
name node1
asset-id 4ebf2ff4-697f-46c8-8992-748e4966046b
device-interface mpls1
name mpls1
type ethernet
pci-address 0000:00:04.0
network-interface mpls1
name mpls1
global-id 3
address 10.0.128.0
ip-address 10.0.128.0
prefix-length 31
gateway 10.0.128.1
exit
exit
exit
device-interface lan1
name lan1
type ethernet
pci-address 0000:00:03.0
link-settings auto
traffic-engineering
enabled false
exit
load-balancing
utilization-high-water-mark 100
utilization-low-water-mark 80
exit
session-optimization
enable-detection true
exit
enabled true
forwarding true
strip-vlan false
promiscuous-mode false
network-interface srv1
name srv1
global-id 4
vlan 0
type external
conductor false
prioritization-mode local
source-nat false
qp-value 0
mtu 1500
enforced-mss disabled
address 192.168.64.1
ip-address 192.168.64.1
prefix-length 24
exit
icmp allow
multicast-listeners automatic
multicast-report-proxy false
dhcp disabled
prefix-delegation false
exit
exit
exit
exit
tenant _internal_
name _internal_
description "Auto generated tenant for internal services"
generated true
exit
service webserver
name webserver
scope public
address 172.16.128.2/32
exit
service _conductor_1
name _conductor_1
enabled true
scope private
tap-multiplexing false
transport icmp
protocol icmp
exit
transport tcp
protocol tcp
port-range 443
start-port 443
end-port 443
exit
port-range 930
start-port 930
end-port 930
exit
port-range 4505
start-port 4505
end-port 4505
exit
port-range 4506
start-port 4506
end-port 4506
exit
exit
address 192.168.7.99/32
access-policy-generated true
access-policy _internal_
source _internal_
permission allow
exit
service-policy _conductor_
share-service-routes false
source-nat network-interface
application-type generic
fqdn-resolution-type v4
generated true
exit
service-policy _conductor_
name _conductor_
description "Auto generated service-policy for conductor services"
lb-strategy proportional
session-resiliency none
path-quality-filter false
best-effort true
max-loss 0.5
max-latency 250
max-jitter 100
transport-state-enforcement reset
generated true
ingress-source-nat network-interface
exit
exit
exit
admin@node1.seabo1#
|
| Conductor Web GUI | Configure Static Route |
|---|
| create a RI | configuration > Authority > Router: seabo1 ADD Routing Instances Type: rt:default-instance
|
| Create a static toute | configuration > Authority > Router: seabo1 > Routing: rt:default-instance ADD Static Routes: Destination: 172.16.128.2/32 Administrative Distance: 1 |
| Create a | configuration > Authority > Router: seabo1 > Routing: rt:default-instance > Static Route: 172.16.128.2/32 ADD Static Route Next Hop List: 10.0.128.1
|
| View FIB |
|---|
| |
|
|
| Add Access Policy to Service |
|---|
|
|
|
|
| Verify Connectivity |
|---|
|
|
|
|
| Configure Service Routes and Use SVR |
|
|---|
| Configure Service Route |
|---|
|
|
|
|
|
|
| Remove Static Route |
|---|
|
|
|
|
| Router configuration |
admin@node1.seabo1# show config running
config
authority
name CompanyX
conductor-address 192.168.7.99
. . .
router seabo1
name seabo1
location Sea
location-coordinates +47.6062-122.3321/
. . .
routing default-instance
type default-instance
static-route 172.16.128.2/32 1
destination-prefix 172.16.128.2/32
distance 1
next-hop 10.0.128.1
exit
exit
exit
|
| View FIB |
|---|
|
|
| Set Service to Private |
|---|
|
|
|
|
| Verify Connectivity |
|---|
|
|
|
|
